 |
|
|||
|
Corner
Angle |
90° |
|||
|
Rake
Angle |
Axial |
+5
|
||
| Radial |
-4°~-6° |
|||
| EXP |
JETMILL HIGH FEED |
Specifications |
| Super
High Feed Endmill |
| |
|
|||
|
Corner
Angle |
90° |
|||
|
Rake
Angle |
Axial |
+5
|
||
| Radial |
-4°~-6° |
|||
|
Cat
No. |
Clamping
Screw |
Clamp
Set |
Wrench |
|
EXP05 |
CSPB-3.5S |
- |
IP-15D |
|
EXP06 |
CSPB-4S |
CSY-15 |
| Work
Material |
Grade |
Vc
(sfm) |
fz
(ipt) |
Feed Rate Plunging fz (ipt) |
| Carbon
Steels (JIS S50C, etc.,<300 HB) |
AH120 AH140 |
300~400 |
.020~.080 |
.008 |
| Alloy
Steels (JIS SCM440, etc.,<300 HB) |
AH120 AH140 |
300~650 |
.020~.080 |
.008 |
| Alloy
Steels (Prehardened steels, etc., 30-40 HRC) |
AH120 AH140 |
250~500 |
.020~.040 |
.004 |
| Cast
Irons (JIS FC250, etc.) |
AH120 |
300~800 |
.030~.100 |
.008 |
INSERTS <Back
to top>
: Stocked Standard
Chicago Warehouse
: Stocked Standard
Japan Warehouse; shipment within 1 weekNOTES:
1. The above values of cutting speed shows the standard speed when overhang length
of tool is below 3D. The cutting speed and the feed rate should be set at the lower
values when overhang length of tool exceeds 3D.
2. Thick and heavy chips are discharged by these TAC mills. Use internal air supply or
air blowing in order to prevent the tool failure.
3. The maximum depth of cut for these TAC mills is 0.060 inch.
4. Full engagement of cutter diameter is recommended for best tool life.
| Cutter
Type |
Cutting Diameter |
Max. Depth of Cut |
Max. Ramping Angle |
Max. Depth of Plunging |
Min. Machining Hole Diameter |
Max. Machining Hole Diameter |
Max.Cutting
Width in |
| EXP05020 |
20mm |
.060 |
3º |
.020 |
1.18 |
1.45 |
.630 |
| EXP05075 |
3/4" |
.060 |
3º |
.020 |
1.18 |
1.45 |
.630 |
| EXP06025 |
25mm |
.060 |
5º |
.040 |
1.30 |
1.85 |
.787 |
| EXP06100 |
1.0" |
.060 |
5º |
.040 |
1.30 |
1.85 |
.787 |
| EXP06032 |
32mm |
.060 |
3º30' |
.040 |
1.85 |
2.40 |
1.06 |
| EXP06125 |
1
1/4" |
.060 |
3º30' |
.040 |
1.85 |
2.40 |
1.06 |
| EXP06040 |
40mm |
.060 |
2º |
.040 |
2.48 |
3.03 |
1.38 |
| EXP06150 |
1
1/2" |
.060 |
2º |
.040 |
2.48 |
3.03 |
1.38 |
| Cat
No. |
Stock |
#
of Teeth |
Dimensions
(inch) |
Applicabale
Inserts |
Shank
Type |
||||
| D |
d |
L |
L1 |
L2 |
|||||
| EXP05075RSU |
|
2 |
3/4 |
3/4 |
4.031 |
2.00 |
2.031 |
WPM*05H315ZPR |
WELDON |
| EXP06100RSU |
|
2 |
1.0 |
1.0 |
4.781 |
2.50 |
2.281 |
WPM*06X415ZPR
|
|
| EXP06125RSBU |
|
3 |
1
1/4 |
1
1/4 |
5.281 |
3.00 |
2.281 |
||
| EXP06150RSU |
|
3 |
1
1/2 |
1
1/4 |
5.781 |
3.50 |
2.281 |
||
INCH
METRIC| Cat
No. |
Stock |
#
of Teeth |
Dimensions
(mm) |
Applicabale
Inserts |
Shank
Type |
||||
| D |
d |
L |
L1 |
L2 |
|||||
| EXP05020RL |
|
2 |
20mm |
20mm |
180 |
100 |
80 |
WPM*05H315ZPR |
STRAIGHT
. |
| EXP05020RS |
|
2 |
20mm |
20mm |
130 |
50 |
80 |
||
| EXP06025RL |
|
2 |
25mm |
25mm |
200 |
120 |
80 |
WPM*06X415ZPR |
|
| EXP06025RS |
|
2 |
25mm |
25mm |
140 |
60 |
80 |
||
| EXP06032RL |
|
2 |
32mm |
32mm |
200 |
120 |
80 |
||
| EXP06032RLB |
|
3 |
32mm |
32mm |
200 |
120 |
80 |
||
| EXP06032RS |
|
2 |
32mm |
32mm |
150 |
70 |
80 |
||
| EXP06032RSB |
|
3 |
32mm |
32mm |
150 |
70 |
80 |
||
| EXP06040RL |
|
2 |
40mm |
32mm |
250 |
50 |
200 |
||
| EXP06040RS |
|
2 |
40mm |
32mm |
150 |
50 |
100 |
||
 |
Cat
No. |
Class |
Grades |
Dimensions
(mm) |
||||||
| AH120 |
AH140 |
T3030 |
A |
B |
T |
R |
0° |
|||
| WPMW05H315ZPR |
M |
|
|
|
5 |
7.94 |
3.5 |
1.5 |
11° |
|
| WPMT05H315ZPR-ML |
M |
|
|
|
5 |
7.94 |
3.5 |
1.5 |
11° |
|
| WPMT05H315ZPR-MH |
M |
|
|
. |
5 |
7.94 |
3.5 |
1.5 |
11° |
|
| WPMW06X415ZPR |
M |
|
|
|
6 |
9.525 |
4.2 |
1.5 |
11° |
|
| WPMT06X415ZPR-ML |
M |
|
|
|
6 |
9.525 |
4.2 |
1.5 |
11° |
|
| WPMT06X415ZPR-MH |
M |
|
|
. |
6 |
9.525 |
4.2 |
1.5 |
11° |
|
Jump to: • Inserts • Parts • Recommended Cutting Conditions • Machining Capabilities
© 2006 Tungaloy America, Inc. I
Comment About This Site